Profile K02 with automatic fixation of rotation unit:
instantaneous turn of clamps by 180 degrees
minimum friction and a clear fixation during a turn
adjustment of smoothness and stiffness of fixation
monolithic milled area for electronic protractors
installation node in the form of a built-in frame
Structure allows for an instant turn of clamps for 180 g, and with the help of a group of bearings, in a system of flat springs, rigidly fix the clamps with a knife. High precision of the parts, in combination with the 5-th bearings, ensures an ideal glide during the turn, as well as the turning unit has an additional function for adjusting the smoothness of the stroke and fixing rigidity.
To change the clamps, the K02 is equipped with a unified installation unit for various types of clamps and accessories. nozzles, this node is made in the form of a frame.
A monolithic milled platform K02 is built-in by default for electronic goniometers. This element provides high comfort and convenience, as well as high accuracy of the measurements, when working on a device with electronic goniometers.
The rack gear is used to convert the rotational motion of the pinion (handle) into the progressive - the rack (vertical rack SHU)
0.8 mm pitch of the rail
A cone pair with a screw drive multiplies the compression of the jaws many times, reducing the load on the screw. Force compression is done manually with the help of light rotation of the side handle, excluding the use of additional tool keys. The conical clamp increases the symmetry of compression due to the distribution of equal elastic loads on the power springs. Cones are made of alloy steel with subsequent heat treatment hardness 47..52 HRC, which will ensure the durability of this unit. The clamping jaws are made of 65G sprung-spring steel, followed by heat treatment, 30..35 HRC - Number of clamping sponges: 2 pcs. - Clamping sponge width: 16 mm. - Minimal distance between the sponges: 20 mm, - Maximal: 170 mm.
The double clamp is recommended to be used for knives with width of 1 to 3.5 mm. , the length is up to 300-350 mm
Swivel symmetrical clip for double-sided grinding without reinstalling of knife. Clamp structure allows to clamp symmetricaly and rigidly knives with complex blade geometry. It has an independent mechanism of reinstall clamping sponges. It's suitable for cutlery and fillet knives with narrow spine. In contrast to single clamp, thin knives can be pinched in double clamp only. Thanks to two clamp points thing knives are pinched more rigidly and they are not bent being in double clamp. But in contrast to single clamp double clamp has more narrow sponge of 16 mm in width therefore knives with spine more that 3.5 mm in width are not recommended to be pinched. Minimal distance between the sponges is 40mm., maximal 130 mm. Recommended knife length for the clamp is 30-300 mm. Minimal knife width 20mm, thickness in spine 3.5 mm, range of angles 10-32 degrees (range can be changed for wide knives). Clamp sponges are made from aglow sprung-spring steel 65 g.Suitable for K-01 model. Sponges, screws and flat springs can be bought separately.
Swivel symmetrical clip for double-sided grinding without reinstalling of knife. Clamp structure allows to clamp rigidly and symmetricaly knives with complex blade geometry. It is perfectly suitable for hunting and folding with wide spine. Narrow spine knives are not recommended to be sharpen using single clamp as it can be bent. Recommended knife lendth for the clamp: 50-200 mm. Minimal knife width 20 mm, spine thickness 5 mm, angle range 10-32 degrees (wide knife range can be different). Clamp sponges are made from aglow sprung-spring steel 65 g. It isn't suitable for K-01 model. Sponges, screws and flat springs can be bought separately.
Special pliers for narrow netting knives with reduced grinding angle. The thin jaws of the clamp are made from spring steel which provides sufficient clamping force. The clamp with the modified configuration of the jaws and the application of the special screws have minimum final sharpening angles of 6.5 g. for each side. It is not recommended to use knives with a thickness of more than 2.5 mm. to avoid damage to sponges. Recommended knife length for pliers: 30-300 mm. The minimum width of the knife is 10 mm, the thickness of the spine is 2.5 mm, the range of angles is 6.5 to 32 degrees (the range wide knife may be different). Suitable for K-01. Sponges, screws and flat springs can be purchased separately.
Increased thickness of the spring provides exceptional clamping stability. They are intended for operations with the raised loading (for example at roughing operation on firm steels).
Material:steel 65G ground, heat-treated; Thickness: 1 mm (standard 0.8 mm); Abrasive load, without deviations: 1 kg (standard 0.5 kg);
The whole milled BLACK clamps (anodized) are made of high-strength aluminum alloy with subsequent protective coating and heat treatment.
The increased spring thickness provides exceptional clamping stability. They are designed for operations with high loads (for example, in a roughing operation on solid steels). span>
Material: 65G steel, ground, heat-treated; Thickness: 1 mm (standard 0.8 mm); Load on abrasive, without deviations: 1 kg (standard 0.5 kg); p>
Special clamp for narrow fillet knives with reduced sharpening angle. Thin clamp jaws are produced from structural spring steel that provides sufficient clamping force. The clamp with amended jaw configuration and special screws application has minimal ultimate sharpening angles 6.5 gr. for each side. It's not recommended to use knives with spine thickness more than 2.5 mm. to avoid damage to the sponges. Recommended knife length for the clamp: 30-300 mm. Minimal knife width 10 mm, spine thickness 2.5 mm, angle range 6,5-32 degrees (wide knife range can be different). Suitable for K-01 model. Sponges, screws and flat springs can be bought separately.
The device for lens knife sharpening from TS Profile, it is presented in the form of replaceable adapters, which are easily mounted on the holder of the abrasive, the adapters provide uniform variation of angles over the entire width of the feeds, as a result of the work, the radius shape of the lens is obtained. The range of angles (radius) is determined by the nozzles, on each nozzle there is a marking with the appropriate range (radius). Easy installation, simple design, low cost, as a result of the radius shape of the lens - these are the main parameters that characterize this device. The kit includes an adapter with a range of 7.2 degrees, mounting hardware.
The device for lens sharpening of the knives by TSPROF is presented in the form of adapter, which are easily mounted on the holder of the abrasive, the adapter ensure a uniform change of angles over the entire width of the feeds, as a result of the work, the radius shape of the lens is obtained.
Angle ranges (radius) are defined by holes, each hole is marked with the appropriate range (radius). Easy installation, simple design, low cost, as a result of the radius shape of the lens - these are the main parameters that characterize this device. This contains adapter with holes for 4.3, 7.2 and 11.3 degrees, a sleeve adapter, fastening kit for mounting and high-precised titanium guide for better control during operation.
TSPROF presents new clamp for our sharpeners - small universal table. With it you can sharpen a variety of cutting tools, sharpening angles which are greater than 45 degrees, for example: scissors, hairdressing tools, carpentry tools.
The small universal table is equipped with two types of clips: a shortened 16 mm sponge and a Y-shaped clamp. For fastening the climps to the base there are three fixing points, which allows sharpening the tool with the most complex geometry of the blade. Clamps are used both together and one by one. The base of the table is whole-milled and has no welds or fasteners. The base is attached to two frame holders with thumbscrews and clamping cylinder. Comfortable wide thumbscrews allow you to firmly fix the position of the table. The versatility of the table is complemented by the fact that the base can be turned in the holders, significantly expanding the range of application of this clamp.
The set includes 5 bars on aluminum forms with bevels 45 gr. This set will be enough for all types of work, from roughing to final grinding. The wear rate is higher than that of Boride abrasives. Stones:
*Stones of green silicon carbide 64C, binder - ceramic. Soak in water, work with water. You can work with oil, a ceramic bunch of oil will not suffer. The stones are quite versatile and are suitable for sharpening a wide range of steels, incl. hard, powder steels with hardness higher than 60 HRC.
The set includes 5 bars on aluminum forms with bevels 45 gr, universal cover. This set will be enough for all types of work, from roughing to final grinding. The wear rate is higher than that of Boride abrasives. Stones:
*Pierres de carbure de silicium vert 64C, liant - céramique. Tremper dans l'eau, travailler avec de l'eau. Vous pouvez travailler avec de l'huile, un tas d'huile en céramique ne souffrira pas. Les pierres sont assez polyvalentes et conviennent à l'affûtage d'une large gamme d'aciers, y compris les aciers durs en poudre d'une dureté supérieure à 60 HRC.
Boride is a well-known brand in the market of abrasives, offering professional sharpening and polishing stones of different sizes and materials. In the Boride range, you can find abrasive stones for absolutely any kitchen knife, and the forty-year experience of the manufacturer guarantees that the grinding and polishing tools of this brand will prolong the life of even the finest blades for a long time.
Ruby 150 1/4*1*6"
Ruby 220 1/4*1*6"
AS-9 320 1/4*1*6"
Golden Star 600 1/4*1*6"
T2 1000 1/4*1*6"
Boride abrasive stones in a cover and on blanks. The blue T2 series is made of aluminum oxide and uses a very hard bond. Due to this, it has high productivity and wear rate is below average. Boride recommends T2 as the best series for working with stainless steel.
T2 150 1/4*1*6"
T2 220 1/4*1*6"
T2 320 1/4*1*6"
T2 600 1/4*1*6"
T2 800 1/4*1*6"
T2 1200 1/4*1*6"
Narrow stones are more convenient for sharpening S-shaped RK, concave blade and cutting tool of small dimensions.
T2 320 1/8*1/2*6"
T2 400 1/8*1/2*6"
T2 600 1/8*1/2*6"
T2 800 1/8*1/2*6"
T2 1000 1/8*1/2*6"
T2 1200 1/8*1/2*6"
Professional natural stone Arkansas Hard (Fine) 800-1000 grit, without a blank.
It is intended for finishing sharpening knives from different steel. It works very cleanly. The stone is ideal for honing pocket, hunting, kitchen knives and tools of any size.
Size: 151х23х6 mm
Production : USA
Narrow stones are more convenient for sharpening S-shaped RK, concave blade and cutting tool of small dimensions.
Dimensions: 1/8 x 1/2 x 6 inch
Grit content: 320, 400, 600, 800, 1000, 1200
Professional natural stone Arkansas Black (Ultra Fine) 2000-3000 grit, without a blank.
Arkansas Black is designed for finishing knives from different steel. It works very cleanly. The stone is ideal for honing pocket, hunting, kitchen knives and tools of any size.
Size 151х23х6 mm
Production : USA
Stripping. Repair work related to the intensive removal of metal. Restore and change the geometry of the knife. It is necessary in those cases where the re-profiling of the cutting edge is required. Suitable for solid powder steels.
Stone dimensions: 200x35x10 mm
Grit dimensions: 200/160 - 160/125 mkm
Concentration of diamond powder: 100%
Natural stone Arkansas is a high-quality stone that can be used for sharpening knives and other cutting tools. This stone comes up with all its competitors and achieves a better final result. The highest grit of this stone creates clean mirror blades and an ideal cutting edge.
Dimensions 151х23х6 mm
Production : USA
Diamond bar of Russian production de l'Usine des outil from the Venev diamond tools factory. Unlike abrasive stones, diamond bars are much less worn, so they are recommended to work with hard steels. Diamond bar - two-sided. The two sides have different granularity, this makes the bar more versatile. The sides are marked with a grain size value. Two-sided Venusian diamond bars with a diamond concentration of 25%, dimensions of 200 * 35 * 10. Grit degree in microns:
Firts bar 160/125- 50/40
Second bar 20/14-7/5
Cases are sold separately, 10$/pcs. (indicate in the commentary field to a manager when completing the order if you need some).
Gray one - for stainless steel, it has a coarse grain; White one - finishing for all kinds of metals. Aluminium oxide. 20/32 μm Recommended for use with leather letterhead.
The set consists of 3 bars, with a 25% concentration of diamond grains, it is recommended to use for sharpening and polishing. These bars work "in a gentle mode" and leave a minimum of risks on the cutting edge.
1. Double-sided diamond bar, 200x35x10 mm, 3 / 2-1 / 0 μm, 25%
2. Double-sided diamond bar, 200x35x10 mm, 20 / 14-7 / 5 μm, 25%
3. Double-sided diamond bar, 200x35x10 mm, 160 / 125- 50/40 μm, 25%
The set consists of 4 bars, with a 100% concentration of diamond grains, this allows you quickly and efficiently perform almost the entire range of knife sharpening tasks, starting from stripping operations, finishing with final polishing of cutting edge.
1. Barre de diamant double face, 200х35х10 mm, 3/2-1/0 μm, 100%
2. Barre de diamant double face, 200х35х10 mm, 20/14-7/5 μm, 100%
3. Barre de diamant double face, 200х35х10 mm, 100/80-50/40 μm, 100%
4. Barre de diamant double face, 200х35х10 mm, 200/160 - 160/125 μm, 100%
The leather blank is intended for final finishing of the cutting edge of the knife. It is clamped in the holder of the abrasive. Leather corrects the unevenness of the cutting edge and strengthens it. The working surface is made of very smooth high-quality cow leather, pasted onto a blank from natural wood. On the velvet side, paste is applied for manual polishing. Editing the knife is done by progressive movements with respect to the angle of sharpening. It is possible to work both with or without paste, or to use the finish one on the smooth side. The dimensions are 170x30x10 mm.
For gourmets and aesthetes. Ideal as a gift. We would like to draw your attention to the corporate case of the German company WAG, made of high-quality plastic. Maximum functionality and attractive design.
The case is equipped with convenient lodges designed specially for the grinding device Profile, everything is thought out to the last detail. Overall dimensions 497 x 411 x 120 mm Design features:
Elegant and convenient latches;
Reliable straight hinges; A reliable carry handle;
High legs provide good case stability; li>
External slides preventing slipping;
Metal base for holding the grinding device on working surface of table or workbench. It serves to fix the body of the device on work surface without using a G-clamp. It allows you to install the device Profile, not tying it to edge of the desktop, is also useful in cases where the use of clamps is difficult. The design of the stand is made in accordance with the overall style of the product, perfectly complements the design, giving the device stability, and the user's confidence and comfort in the process of sharpening. To fix the case of the device on the stand, install it in a specially designed seat and tighten the fixing screws. The heads of the screws are made in the form of lambs and are tightened by hands without the use of keys. Upon the end of work, loosen the screw connections and freely remove the device casing from the stand.
Share your experience in knife sharpening, discuss the results of sharpening with your collegues, take pictures of idealy acute blade, compare different sharpening technics, abrasives and sharpening tools.
The cover is designed for 6 seats, the maximum length of the stone is 160 mm. It is supplied with Velcro tape to cover the contents. On the bag there is a signature badge "TC Профиль".
The blanks allow to clamp stones more confidentely and protect them from damages as well.
It allows you to see the burrs, check the angle of sharpening along the entire length of the blade, objectively assess the sharpness and polishing of the blade, see the blade with a large increase and achieve an ideal grinding.
Updated narrow abrasive holder::
Perfect way to work with narrow abrasives. 150x12x3mm size, for sharpening recurve, concave and convex blades, for pocket knifes and folding multitool knives like Victorinox. Low weight, excellent handling and an overview of the cutting edge during operation.
The design of holder has been improved, now it lighter and thinner, weight only 100 grams.
Stiffness of holder was increased! Due to the tight fit of the support plate to base rod.
Solid machined clamps made of aluminum alloy Д16Т (Russian analog of 2024) and precisely oriented in the axial direction by means of a supporting plate made of polished stainless steel and rod.
Abrasive tool placed as close as possible to the longitudinal axis of the holder, which significantly improves the control over the movements of the stone during sharpening. - Abrasive holder features convenient and simple place for digital protractor.
New construction more ergonomic and leaves pleasant feelings while working
Convenient abrasive holder allows to fast re-mount stones, blanks and etc.
The carrier plate along the long bar provides additional rigidity to the mounting of abrasive stones and relieves excessive loads, this plate gives you the opportunity to work with fragile stones without the aluminium blanks. Distance from the handle to the stone do not depends on the length of the abrasive, this increases the control during finishing operations.
The kit comes with two spacer rings with damper, one of the rings works as a parking unit.
Abrasive holder bevels 90 +45 degrees
Jaws: width - 18/16mm; the width of the support plate - 16mm; operating height - 5mm (groove height for 45 degree, 3mm).
Min/Max size of abrasive: 105/175mm long
Durable, soft nylon cover for carrying and storing abrasive stones up to 210 mm long. it is equipped with a Velcro strap to hold the stone and the "Tsprof" badge.
High-precision digital tool for measuring sharpening angle.Features:
Low battery indication
Body material: Aluminium
Precision: 0.1 degrees
Working temperature: 0-40 Celsius degrees
Voltage: 3V/DC (CR2032x3)
Max current: 3mA
Professional set of wrenches for TSPROF Sharpener, ideal for all types of clamps,as well as to configure the hinge unit, flipping mechanism and the adjusting the pad under the digital protractor.
Wrenches are made from high aloy steel and heat treating and grinding the working surfaces, which guarantees high precision, durability and resistance to break.
Due to the presence of ergonomic ribbed handle keys are easy to use, the main handle provides a secure hold of the tool and high torque, and the additional (upper) handle designed for rapid rotation.
The keys are equipped with a compartment to store spare screws and others.
The set comes with 4 HEX key sizes:
Handle diameter: 18mm
Total length (adjustable): 100 to 195 mm
Handle length: 90 mm
Blanks made from plexiglas (thickness 6mm) for abrasive size 170x30x6mm are recommended to be used with sandpaper for hardness.
This device is quite useful tool in knife sharpening to control blade condition on highest magnification. Allows you to see any burr, control sharpening angle on all over the blade length, estimate blade sharpness and blade polishing objectively, see blade in detail to achieve perfect sharpening.
Calculator of sharpening systems
30+ items to create your own sharpener
The amount of your order, excluding shipping costs: